/
/
/
EM-Tec gripping stub and stub based vise holders

EM-Tec gripping stub and stub based vise holders

The EM-Tec gripping stub and stub based vise holders are useful to grip and hold SEM samples without much need for sample preparation. Ideal for cross-section and edge-on imaging. The comprehensive selection of this type of cost-effective gripping and vise type holders is compatible with SEMs using pin stubs (FEI, Zeiss, Tescan, Phenom, Aspex), SEMs using M4 thread (Hitachi and EM-Tec SEM stage adapters) and JEOL SEMs.

EM-Tec GS24 gripping stub holder with clamping plate, 0-4mm, aluminium, pin

EM-Tec GS24 gripping stub with clamping plate to hold cross section samples or tissue up to 4mm thickness. Sample is held by the clamping plate which is pushed with set screws. Also useful for holding tissue for dehydration and CPD processing. Holder dimensions are 24x12x12mm, standard Ø3.2mm pin.

EM-Tec GS24 gripping stub holder with clamping plate, 0-4mm, aluminium, pin
Product # Unit
12-000234 each

EM-Tec PS4 mini pin stub vise clamp 0-4mm, Ø12.7×7.2mm, pin

EM-Tec PS4 mini pin stub vise clamp for sample thickness from 0-4mm. The sample is held vertically with a small set screw. Most effective way to study cross sections of thin samples. Holder size w/o pin is Ø12.7×7.2mm.

EM-Tec PS4 mini pin stub vise clamp 0-4mm, Ø12.7×7.2mm, pin
Product # Unit
10-002240 each

EM-Tec PV5 mini vise sample clamp, pin

EM-Tec PV5 mini sample vise clamp for sample thickness from 0-5mm. The sample is held vertically between the vise jaws. The vise jaws are tightened by a brass thumb screw. Holder size w/o pin is Ø12.2x17mm.

EM-Tec PV5 mini vise sample clamp, pin
Product # Unit
12-002209 each

EM-Tec PS44 quad vise stub holder for 4 samples from 0-4mm, pin

The samples are held vertically with 4 small set screws. Most effective way to study cross sections or thin samples. Holder size w/o pin is Ø25.4 x 7.2mm. Standard pin.

EM-Tec PS44 quad vise stub holder for 4 samples from 0-4mm, pin
Product # Unit
10-002244 each

EM-Tec PS6 mini split pin stub vise clamp 0-6mm, Ø12.7×7.2mm, pin

EM-Tec PS6 mini pin stub split vise clamp for sample thickness from 0-6mm. The sample is clamped between the two min vise clamps. The split vise jaws are closed by an allen screw. Closed split vise diameter is 12.7mm; when opened it is 19×12.7mm.

EM-Tec PS6 mini split pin stub vise clamp 0-6mm, Ø12.7×7.2mm, pin
Product # Unit
10-002218 each

EM-Tec PS7 mini pin stub dual slot vise clamp, 2x1mm, Ø15x6mm, pin

EM-Tec PS7 mini pin stub dual slot vise with two slots of one mm wide. Ideal for holding thin wafer pieces samples for cross section imaging. Samples are clamped by set screws. Holder size w/o pin is Ø15x6mm.

EM-Tec PS7 mini pin stub dual slot vise clamp, 2x1mm, Ø15x6mm, pin
Product # Unit
10-002242 each

EM-Tec PS12 pin stub vise clamp 0-12mm, Ø25×7.2mm, pin

EM-Tec PS12 pin stub vise clamp for sample thickness from 0-12mm. The sample is held vertically with a set screw. Most effective way to study cross section of thin samples. Holder size w/o pin is Ø25x6mm.

EM-Tec PS12 pin stub vise clamp 0-12mm, Ø25×7.2mm, pin
Product # Unit
12-000112 each

EM-Tec PS9 mini split mount vise 0 – 8mm, pin

EM-Tec PS9 mini split mount vise clamp for sample thickness from 0-8mm. The sample is clamped between the two jaws of the split mount. The split mount vise jaws are closed by two allen screws. Closed mini split mount vise dimensions without pin are Ø15x10mm; when opened 23x15x10mm.

EM-Tec PS9 mini split mount vise 0 – 8mm, pin
Product # Unit
12-000230 each

EM-Tec GS24 gripping stub holder with clamping plate, 0-4mm, aluminium, M4

EM-Tec GS24 gripping stub with clamping plate to hold cross section samples or tissue up to 4mm thickness. Sample is held by the clamping plate which is pushed with set screws. Also useful for holding tissue for dehydration and CPD processing. Holder dimensions are 24x12x12mm x M4.

EM-Tec GS24 gripping stub holder with clamping plate, 0-4mm, aluminium, M4
Product # Unit
12-000334 each

EM-Tec HS6 mini M4 cylinder stub vise clamp 0-6mm, Ø15x10mm, M4

EM-Tec HS6 mini M4 cylinder stub vise clamp for sample thickness from 0-6mm. The sample is held vertically with a small set screw. Simple and cost-effective way to clamp cross sections of thin samples. Holder stub size is Ø15x10mmxM4.

EM-Tec HS6 mini M4 cylinder stub vise clamp 0-6mm, Ø15x10mm, M4
Product # Unit
12-000306 each

EM-Tec HV5 mini vise sample clamp, M4

EM-Tec HV5 mini sample vise clamp for sample thickness from 0-5mm. The sample is held vertically between the vise jaws. The vise jaws are tightened by a brass thumb screw. Holder size is Ø12.2x17mmxM4.

EM-Tec HV5 mini vise sample clamp, M4
Product # Unit
12-003209 each

EM-Tec HS15 M4 cylinder stub vise clamp 0-16mm, Ø25x10mm, M4

EM-Tec HS15 M4 cylinder stub vise clamp for sample thickness from 0-16mm. The sample is held vertically with a set screw (multiple lengths are supplied). Cost effective and practical small vise clamp base on the stub size of Ø25x10mmxM4.

EM-Tec HS15 M4 cylinder stub vise clamp 0-16mm, Ø25x10mm, M4
Product # Unit
12-000315 each

EM-Tec HS7 mini M4 cylinder stub dual slot vise clamp, 2x1mm, Ø15x6mm, M4

EM-Tec HS7 mini pin stub dual slot vise with two slots of one mm wide. Ideal for holding thin wafer like samples for cross section imaging. Sample are clamped by set screws. Holder size is Ø15x6mm, M4 threaded hole.

EM-Tec HS7 mini M4 cylinder stub dual slot vise clamp, 2x1mm, Ø15x6mm, M4
Product # Unit
12-000328 each

EM-Tec HS9 mini split mount vise 0 – 8mm, M4

EM-Tec HS9 mini split mount vise clamp for sample thickness from 0-8mm. The sample is clamped between the two jaws of the split mount. The split mount vise jaws are closed by two Allen screws. Closed mini split mount vise dimensions are Ø15x10mm; when opened 24x15x10mm. M4 threaded hole in the base.

EM-Tec HS9 mini split mount vise 0 – 8mm, M4
Product # Unit
12-000330 each

EM-Tec JS4 mini cylinder stub vise clamp 0-4mm, JEOL Ø12.2x10mm

EM-Tec JS4 mini cylinder stub vise clamp for sample thickness from 0-4mm. The sample is held vertically with a small set screw. Most effective way to study cross section of thin samples. Holder stub size is Ø12.2x10mm.

EM-Tec JS4 mini cylinder stub vise clamp 0-4mm, JEOL Ø12.2x10mm
Product # Unit
12-000504 each

EM-Tec JV5 mini vise sample clamp, JEOL Ø12.2mm stub base

EM-Tec JV5 mini sample vise clamp for sample thickness from 0-5mm. The sample is held vertically between the vise jaws. The vise jaws are tightened by a brass thumb screw. Compatible with holders for the Ø12.2x10mm JEOL stub with a height of 17mm above the stub.

EM-Tec JV5 mini vise sample clamp, JEOL Ø12.2mm stub base
Product # Unit
12-000509 each

EM-Tec JS12 cylinder stub vise clamp 0-12mm, JEOL Ø25x10mm

EM-Tec JS12 cylinder stub vise clamp for sample thickness from 0-12mm. The sample is held vertically with a set screw (multiple lengths are supplied). Cost effective and practical small vise clamp based on the stub size of Ø25x10mm.

EM-Tec JS12 cylinder stub vise clamp 0-12mm, JEOL Ø25x10mm
Product # Unit
12-000512 each

Your Laboratory Partner

Since 1998, Media System Lab has focused its attention on Quality Research and Attention to Customer needs

Contact us to learn more about EM-Tec gripping stub and stub based vise holders

Share on facebook
Share on google
Share on twitter
Share on linkedin
Share on whatsapp
Share on facebook
Share on google
Share on twitter
Share on linkedin
Share on whatsapp
×

Ciao, clicca qui sotto per comunicare con il nostro staff via Whatsapp

×